×

Message

EU e-Privacy Directive

This website uses cookies to manage authentication, navigation, and other functions. By using our website, you agree that we can place these types of cookies on your device.

View e-Privacy Directive Documents

Print

UPDATED 4/4/2013 - 8el, 9el, 10el, 12el & 14el Yagis for 144MHz listed and added to 'New 2013 Yagis' link in top menu

 

 The Very Latest G0KSC designs only available from InnovAntennas

A new line of long OWL Yagis by G0KSC

Those that read DUBUS magazine will be aware that G0KSC introduced the world to the concept to of wide band, low impedance designs.

Yagis with excellent performance became commonplace within the ham community when K6STI first introduced YO (Yagi Optimiser) and AO (Antenna Optimiser). However, while these programs made Yagi design/optimisation easy, users were often blinkered by gain objectives and pushed their software tools for optimum gain. The easy route to gain is boom length and the power of thesoptimisers meant the boom could be extended, SWR dipped and once more the boom extended until such time that a Yagi was created with very narrow bandwidth that was unstable in wet weather conditions. Those 'that knew' would choose OWA (Optimised Wideband Arrays) which used split dipole feed systems exhibiting a perfect 50Ohm feed because although these were slightly lower in gain and did not posses such good F/B, they remained stable in terms of SWR, impedance and performance over much wider bandwidths than lower impedance antennas.

The fact is now as it was then, a lower impedance antenna can be better (in all performance attributes) than a 50Ohm split dipole antenna. The belief that low impedance meant narrow band was simply through miss-use of the optimiser tools available. Different design criteria need to be taken into account when optimising lower impedance antennas, part of this is the concentration of the first few elements within the Yagi ('the driver cell' to coin a term used by DG7YBN http://dg7ybn.de/index.htm) and the optimisation of the Yagi within the Elevation plane rather than the azimuth plane (I am please to see ham antenna developers both home and abroad have adopted this approach for cleaner patterns now which was first used by my mentor YU7EF www.yu7ef.com).

So what impedance is best?

Honestly I would have to say for the best balance of gain, F/B and bandwidth (by bandwidth I mean the flat-line of SWR, Gain and F/R (Front to Rear)). Martin, DK7ZB's (http://www.qsl.net/d/dk7zb/) 28Ohm is about as good as it gets. However, while I have modelled, built, experimented with and used 28Ohm Yagi antennas, my goal remains to be one were the driven element is arranged or shaped in such a way as to provide a 50Ohm direct feed. A low impedance Yagi that self-matches in its own structure to 50Ohm.

There is nothing wrong with the DK7ZB match (while on the subject of DK7ZB) in fact, it is far better than any other matching arrangement I have seen because it is not another metallic structure attached to the driven element (that is not modelled in the design phase) causing all sorts of pattern distortion, it is coax sitting at the point in the boom where coax would be and if at the point where the 2 x 75Ohm coax cable join to your 50Ohm line, the braid is connected to the boom, there is no need for a balun either, two jobs in one without any distortion. The challenge of making something 50Ohm by means of using a different type of driven element to the split dipole was exciting and a direction perhaps others had not explored. There was no where for me to go with a 50Ohm split dipole Yagi. As much as I tried using various different optimisation methods, YU7EF had it pretty much spot on in almost every case so the ultimate Yagi had to be elsewhere, away from 50Ohm split dipole types.

In one of my DUBUS articles several years ago, I spoke of optimising a 50Ohm split dipole Yagi between 144MHz and 145MHz for best performance and comparing it with the same Yagi now optimised with a 40Ohm feed point impedance (still split dipole). I could achieve better performance in terms of gain and F/B on the 40Ohm Yagi than I could on the 50Ohm Yagi or I could optimise the 40Ohm Yagi for the same performance over a wider bandwidth. It was clear then, lower impedance could be better. The OWL came from the abilities of the folded dipole which has a 4:1 transformation ability. This meant I could model a 12.5Ohm Yagi, add a folded dipole and it became a 50Ohm direct fed antenna with a noise reducing closed loop feed system. Nothing new there, this had been done before but when added to a wide band 12.5Ohm Yagi that was stable in all weathers, the benefits were clear to see.

The OWL (Optimised Wideband Low impedance) Yagi was born

This new low impedance wideband design was called the OWL and again was first published in DUBUS magazine (www.dubus.org). since then I have made many developments and improvements to this design although few designs have been published on this site over the last year or two since the start up of my own antenna company InnovAntennas (www.innovantennas.com Europe and ROW www.innovantennas.us North & South America) where I have designed and developed variants of my designs (LFA, OWL, OP-DES & LFA-Q) for commercial, government and military applications. However, this year will be different. I have a long list of OWL designs with G/T busting performance figures on 144MHz and an excellent balance of gain and bandwidth on 50MHz & 70MHz. Attention to detail has been paid on the suppression of the pattern in all other areas than forward-facing with careful and time consuming (and sometimes tedious!) optimisation again and again moving the control parameters forward 1 degree at a time before performance starts to drop off (indicating a limit has been reached).

I will start with a range of long 2m Yagis, the first being modelled using 8mm diameter elements. the reason for choosing this size is the 5/16'' in Imperial measurement is 7.98mm so the same sizing can be used within the UK, US Europe and rest of world too. so lets have a look at some plots of this 14el OWL on an 8.9m boom:

 Note the very fast drop off to high suppression either side of the antenna from the 45 degree line backwards. This is key in ensuring you receive no unwanted noise (from directions other than which your antenna is facing).

 

Pattern Symmetry - if you can achieve it, why not do it? This is one of the many design traits I took from the master of clean Yagis, YU7EF

 

This super-clean antenna when placed 10m above ground is a serious performer.

A nice flat, SWR curve where it is needed to be. No need to go silly here, just give the antenna 'band pass filter' characteristics where it is needed.

Performance:

Gain @144.1MHz: 16.56dBi

F/B @144.1MHz: 34.14dB

SWR/Performance bandwidth: better than 1:1.2 from 144-144.8MHz

Sky Temperature (single antenna): 220.2 Kelvin

G/T (single antenna): -6.83dB

Stacking Distances: 4.13m Vertically 4.34m Horizontally

4 x Sky Temperature: 215.8 Kelvin

4 x G/T: -0.54dB GT

VE7BQH table comparisons with other antennas of the same size (bay of 4 antennas, DL6WU Stacking distances):

Antenna      Length (wl)     Gain single antenna (dBd)     Temperature (Kelvin)     G/T (dB)    SWR across 1MHz

YU7EF 15M           4.68                            14.59                  221.7                      -0.89             1.03:1

DK7ZB 14             4.73                            14.92                  233.0                      -0.65             1.50:1

G0KSC 14             4.73                            14.79                  215.8                      -0.54             1.17:1

DG7YBN 16           4.74                            14.79                  221.4                      -0.60             1.18:1

G0KSC 15 LFA      4.75                            14.72                  213.2                       -0.55            1.17:1                  

Notes: The lower the temperature figure, the better. The more positive the G/T figure, the better the antenna is for receiving weak signals. 1MHz bandwidth normalised to best 1MHz bandwidth not 144Mhz to 145Mhz              

There is no one perfect stacking arrangement for EME, don't be mislead here. For your needs, mail me and we will work out what is best for you.

So here are the details for this one if you want to go build it yourself.

Boom positions:

Ref: 0

DE: 99mm (12mm DE. email for different sizes)

D1: 266mm

D2: 639mm

D3: 1225mm

D4: 1936mm

D5: 2740mm

D6: 3571mm

D7: 4447mm

D8: 5328mm

D9: 6229mm

D10: 7140mm

D11: 8072mm

D12: 8899mm

Element Lengths

Ref: 1028mm

DE: 990mm

D1: 964mm

D2: 944mm

D3: 924mm

D4: 905mm

D5: 893mm

D6: 884mm

D7: 876mm

D8: 867mm

D9: 858mm

D10: 845mm

D11: 828mm

D12: 834mm

 

Pitfalls and Cliffs

If you want to use a folded dipole, mail me. I will help you calculate the sizes of this both width and height for your chosen boom diameter

DON'T offset a folded dipole and expect to have the nice clean pattern you have seen above, it will not happen. Any change needs to be modelled and checked. If a folded dipole is offset, the elevation plane pattern will be distorted. However, this distortion can be used to your advantage (noise reduction) especially when stacking. For out side of the square scenarios like this, mail me.

It is perfectly expectable to use the DK7ZB twin 50Ohm coax match on a split dipole version of this antenna. However, ensure you measure the coax you will use to check its exact velocity factor (VF). If this is wrong, the transformer will not work correctly. I have not found any coax that fits the specified (manufacturers) suggested VF and of course this VF will change with frequency! If you do not have an antenna analyser, borrow one!

There is NO CORRECTION added to any element lengths. If you follow my mechanical construction guidelines, nothing will need to be added at all. DO NOT use any insulators where bolts pass through the boom and element without establishing correction factors, your antenna elements will need to be lengthened should you chose to go down this route.

Any questions just ask. Within this next few weeks, I will add this antenna to as new category and will add another version.

THIS ANTENNA IS NOT FOR COMMERCIAL USE OF ANY KIND

References and other excellent antennas to self build:

DK7ZB - http://www.qsl.net/d/dk7zb/

DG7YBN - http://dg7ybn.de/index.htm

YU7EF - www.yu7ef.com

YU7XL - http://www.qslnet.de/member/yu7xl/

DUBUS Magazine - http://www.dubus.org/

My writing and Yagi development updates can be found in the pages of DUBUS

 

Copyright G0KSC 2013 - All rights reserved